Home > FASTENERS > CHAIN, CABLE, ROPE > CHAIN / ACCESSORIES
Choose a sub category:
CHAIN - PROOF COIL CHAIN - HIGH TEST CHAIN - STRAIGHT LINK
CHAIN - TWIST LINK CHAIN - JACK CHAIN - TWIN LOOP
CHAIN - SASH CHAIN - DECORATIVE CHAIN - PLASTIC
CHAIN - SPECIALTY GRAB HOOKS SLIP HOOKS
CHAIN - COLD SHUTS CHAIN - LAP LINKS CHAIN - QUICK LINKS
CHAIN - SNAP LINKS CHAIN - SWIVELS CHAIN - CLEVIS LINKS
SPECIALTY FARM HITCH PINS ANCHOR SHACKLES
CLEVISES & PINS SNAPS WELDED RINGS
CHAIN HOISTS LOAD BINDERS POWER HOISTS
Sort By:
1 2 3 ... 16
Campbell T7665012 Welded Ring Campbell T5950124 Repair Lap Link National Hardware 3152BC Lap Link
Campbell Welded Ring, Working Load Limit: 200 lb, Ring Diameter: 1 in ID, Chain Size: #7, Steel, Nickel-Plated For connections of chain and attachments (Not for overhead lifting). Do Not exceed working load limit. National Hardware 3152BC Lap Link, Working Load Limit: 120 lb, Trade Size: 1/8 in, Steel, Zinc
National Hardware 3152BC Lap Link SHUT COLD ZINC PLATED 3/16IN Campbell T7665032 Welded Ring
National Hardware 3152BC Lap Link, Working Load Limit: 225 lb, Trade Size: 3/16 in, Steel, Zinc Designed as a temporary chain link repair, use one size bigger than chain. Can be used to couple chain attachments. Do not reuse after closure. Manufactured from steel. Campbell Welded Ring, Working Load Limit: 200 lb, Ring Diameter: 1-1/4 in ID, Chain Size: #7, Steel, Nickel-Plated
Fehr Bros 3/16 Anchor Shackle Campbell T7660841 Welded Ring Campbell T7661152 Welded Ring
Forged steel, hot dipped, galvanized. Open-throat design, wide bow, screw pin shackle requires no tools to assemble. Slip screwdriver blade or hand punch through pin/eye and tighten. Warning, Inspect regularly. Replace if worn, distorted or damaged. Ensure pin is fully engaged. Seize pin with wire. Do not exceed WLL [Work Load Limit]. Use only duty rated shackles, with embossed WLL, for overhead lifting. Campbell Welded Ring, Working Load Limit: 200 lb, Ring Diameter: 1-1/4 in ID, Chain Size: #4, Steel, Zinc Campbell Welded Ring, Working Load Limit: 200 lb, Ring Diameter: 2 in ID, Chain Size: #3, Steel, Nickel-Plated
National Hardware 3152BC Lap Link SPRING SNAP STEEL ZN 3/16 Campbell T7665042 Welded Ring
National Hardware 3152BC Lap Link, Working Load Limit: 500 lb, Trade Size: 1/4 in, Steel, Zinc Do not exceed the working load limit. Do not use for overhead lifting, to support human weight, for playground or athletic equipment or as safety device. Campbell Welded Ring, Working Load Limit: 200 lb, Ring Diameter: 1-1/2 in ID, Chain Size: #3, Steel, Nickel-Plated
Fehr Bros 1/4IN Anchor Shackle Campbell T4900424 Cold Shut Campbell T4900324 Cold Shut
Forged steel, hot dipped, galvanized. Open-throat design, wide bow, screw pin shackle requires no tools to assemble. Slip screwdriver blade or hand punch through pin/eye and tighten. Warning, Inspect regularly. Replace if worn, distorted or damaged. Ensure pin is fully engaged. Seize pin with wire. Do not exceed WLL [Work Load Limit]. Use only duty rated shackles, with embossed WLL, for overhead lifting. Connections for chain and attachments. When using cold shuts with chain, use one size larger than chain size. With a hammer, drive the open end through the cold shut eye then peen the extended end to prevent opening. Note: Cold shuts should not be reused after closure has been made. Do not use for overhead lifting. Connections for chain and attachments. When using cold shuts with chain, use one size larger than chain size. With a hammer, drive the open end through the cold shut eye then peen the extended end to prevent opening. Note: Cold shuts should not be reused after closure has been made. Do not use for overhead lifting.
BREACHING SNAP ZN 2-1/2 Midland Big Orange 081163/MC645G Anchor Shackle Baron 1407 Open Eye Spring Snap
BARON Bit Snap, Working Load Limit: 80 lb, Snap Opening Size: 5/16 in, Steel, Zinc, Dimensions: 2-1/2 in L Meets requirements of Federal Specification RR-C-271D Amendment 1. Shackle pins are forged from alloy steel, heat treated and tempered to give greater strength. Galvanized per ASTM A153. Design factor 5:1. BARON Chain Snap, Working Load Limit: 60 lb, Snap Opening Size: 9/32 in, Steel, Zinc, Dimensions: 3-3/8 in L
Baron 2450-1/4 Snap Link National Hardware 3153BC Cold Shut National Hardware 3153BC Cold Shut
Do not exceed the working load limit. Do not use for overhead lifting, to support human weight, for playground or athletic equipment or as safety device. National Hardware 3153BC Cold Shut, Working Load Limit: 1250 lb, Trade Size: 1/4 in, Steel, Zinc National Hardware 3153BC Cold Shut, Working Load Limit: 1900 lb, Trade Size: 5/16 in, Steel, Zinc
SPRING SNAP RNDEYE SWVL 3/8 Campbell T7665001 Welded Ring Campbell T4900524 Cold Shut
BARON Spring Snap, Working Load Limit: 45 lb, Zinc, Nickel, Dimensions: 2-5/8 in L Campbell Welded Ring, Working Load Limit: 200 lb, Ring Diameter: 2 in ID, Chain Size: #7B, Steel, Nickel-Plated Connections for chain and attachments. When using cold shuts with chain, use one size larger than chain size. With a hammer, drive the open end through the cold shut eye then peen the extended end to prevent opening. Note: Cold shuts should not be reused after closure has been made. Do not use for overhead lifting.
SHUT COLD ZINC PLATED 3/8IN SNAP LINK 9/32 National Hardware 3155BC Ring
Designed as a temporary chain link repair, use one size bigger than chain. Can be used to couple chain attachments. Do not reuse after closure. Manufactured from steel. Do not exceed the working load limit. Do not use for overhead lifting, to support human weight, for playground or athletic equipment or as safety device. National Hardware 3155BC Welded Ring, Working Load Limit: 195 lb, Ring Diameter: 1 in ID, Chain Size: #7, Steel, Zinc
SPRING SNAP RNDEYE SWVL 1/4 National Hardware 3116BC Bit Snap Baron 5300-3/8 Round Eye Swivel Bolt Snap
BARON Spring Snap, Working Load Limit: 20 lb, Snap Opening Size: 3/16 in, Steel, Zinc, Dimensions: 1-7/8 in L National Hardware 3116BC Bit Snap, Working Load Limit: 115 lb, Snap Opening Size: 5/16 in, Steel, Zinc, Dimensions: 1-3/4 in L BARON Bolt Snap, Snap Opening Size: 1/4 in, Zinc, Nickel, Dimensions: 2-1/4 in L
   
 
1 2 3 ... 16