Home > HEATING & COOLING > HEAT & AIR CONDITIONING > HEATERS
Choose a sub category:
KEROSENE HEATERS-CONVECT/RADIA KEROSENE HEATER ACCESSORIES KEROSENE FUEL
OIL HEATER ACCESSORIES PORTABLE ELECTRIC HEATERS ELECTRIC WALL & CEILING HEATER
GAS HEATERS - NAT GAS HEATERS - LP GAS HEATER ACCESSORIES
PROPANE HEATERS TORPEDO HEATERS OUTDOOR & PATIO HEATERS
UTILITY HEATER PARTS & ACC RADIATOR VALVES
Sort By:
1 2 3 ... 9
CHART WICK HTR KEROSENE CRTG FLTR OIL 10U 25GPH REPL FTG HTR LP HEATERS BRS
Kero World Kerosene Heater Wick Chart, Dimensions: 0.05 x 8.5 x 11 in 10-micron wool felt. Center core bonded to prevent media migration. Male pipe thread x left hand male thread.
MANUAL SIPHON PUMP ASSY HOS 9/16IN LT HND MPT BRS CRTG FLTR OIL 10U 25GPH REPL
Necessary for transfer of fuel from storage tank to heater. Easy to operate utilizing a large ball type siphon. Compatible with all types of kerosene heaters. Male pipe thread x left hand male thread. 10-micron wool felt. Center core bonded to prevent media migration.
ADAPT CYL LP HEATERS BRS IGN Kerosene HTG C Dyna-Glo IGN Kerosene Kerosene HTR
Male pipe thread x left hand male thread. Igniters are an important component of correct heater operation. By using an igniter you can avoid unnecessary dirt and damage caused by match lighting. Igniters are an important component of correct heater operation. By using an igniter you can avoid unnecessary dirt and damage caused by match lighting.
LEAD THMOCPL 12-1/2IN ADAPT CYL LP HEATERS BRS ADAPT CYL LP HEATERS BRS
Replacement part for most Mr. Heater tank top models. Proir to 2011. 1/4 in male pipe threat. Restricted flow, soft nose P.O.L. Most commonly used to connect 1/4 in female pipe thread to 7/8 in female P.O.L. "Soft nose P.O.L. Most commonly used to connect 9/16"" female left hand thread to 7/8"" female  P.O.L."
VLV MIP 10PSI 1/8IN ANG PLG FILL CYL LP HEATERS ADAPT CYL THROWAWAY LP HEATERS
"1/8"" angle MIP. Maximum operating pressure 5 PSI. Maximum pressure 10 PSI." 7/8 in female P.O.L. x male plug. For use with Mr. Heater's Gas Mate ll Quick Connect Coupling kit F276330. Use L.P gas fill plug for filling the tank with the Gas Mate ll in place. CSA certified. UL approved. 1/4 in male pipe thread x 1 in -20 female throwaway cylinder thread.
NUT CPLG 1/4IN MPT LP GRL SYS NZL SPRY 0.65gph 80deg 100psi NZL SPRY 0.5gph 90deg 100psi
End fitting for Type 1, QCC-1 gas grill systems. For appliances with 80,000 Btu or less. Threaded shut-off, excess flow safety. Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners. Mainly used on burners with a hollow cone air pattern and for throughputs up to 2 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
NZL SPRY 0.75gph 60deg 100psi NZL SPRY 1gph 80deg 100psi NZL SPRY 0.75gph 80deg 100psi
Mainly used on burners with a hollow cone air pattern and for throughputs up to 2 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. Mainly used on burners with a hollow cone air pattern and for throughputs up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
NZL SPRY 1.1gph 80deg 100psi NZL SPRY 1.25gph 80deg 100psi NZL SPRY 0.65gph 60deg 100psi
Mainly used on burners with a hollow cone air pattern and for throughputs up to 2 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. Mainly used on burners with a hollow cone air pattern and for throughputs up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. Mainly used on burners with a hollow cone air pattern and for throughputs up to 2 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
NZL SPRY 0.85gph 80deg 100psi NZL SPRY 1.35gph 60deg 100psi NZL SPRY 1gph 60deg 100psi
Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners. Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners. Mainly used on burners with a hollow cone air pattern and for throughputs up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
NZL SPRY 0.75gph 80deg 100psi NZL SPRY 0.65gph 90deg 100psi NZL SPRY 1.25gph 90deg 100psi
Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners. Mainly used on burners with a hollow cone air pattern and for throughputs up to 2 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. Mainly used on burners with a hollow cone air pattern and for throughputs up to 2 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.
   
 
1 2 3 ... 9